🥅 Ford Focus Mk2 Torque Settings

Pipe101 Discussion starter. 130 posts · Joined 2010. #1 · Jun 30, 2020. Im looking at putting my head back on the car after replacing valve stem seals. Who has the torque settings they would like to share. Many thanks. Reply Like. Sort by Oldest first. Screw new spark plugs and tighten them. Use the spark plug socket #16. Use a torque wrench. Tighten it to 25 nm torque. Replacement: spark plugs – Ford Focus MK2. Professionals recommend: WWW.AUTODOC.CO.UK 7–14 Don't tighten the plugs with excessive force. Exceeding tightening torque can damage the thread connection. The stock settings for the RS have been measured to produce about 322 HP as well as 352 Ib-ft torque, but the max estimated horsepower for the Focus RS is 350 HP with 441 Ib-ft torque. Popular upgrades to increase power and handling include an ECU flasher and a high-flow air filter. 62 posts · Joined 2007. #3 · Apr 13, 2015. vieplis said: Torque information from Haynes and Etis, in Nm (and from Haynes in lbf ft): Front caliper carrier bolts - 200 Nm (148 lbf ft); Front caliper slide pins - 28 Nm (21 lbf ft); Rear caliper carrier bolts - 110 Nm (81 lbf ft); Rear caliper slide pins - 35 Nm (26lbf ft). 238 posts · Joined 2004. #10 · Sep 20, 2004. I recently picked up a Great Neck click type torque wrench for $19.99, so they're not that expensive. The idea of using a torque wrench on lug nuts isn't really to hit a specific torque as much as to keep them equal. Official High Anxiety Poster Child [doorpeek] Save. Replacement: engine oil and filter – Ford Focus MK2. Tip from AUTODOC: REPLACEMENT: ENGINE OIL AND FILTER – FORD FOCUS MK2. USE THE FOLLOWING PROCEDURE: 1 Open the hood. WWW.AUTODOC.CO.UK 3–21 Replace the oil filter every time when changing motor oil. All work should be done with the engine stopped. Wear gloves to prevent contact with hot 1885 posts · Joined 2006. #2 · Aug 17, 2011. arniedavo said: as above anybody no the torque setting for eibach spacer nuts ? (nuts on spacer that fit to original huI'm. im thinking 130Nm like normal ?? thanks folks. I'm sure i read it's 130nm thats what i have done mine to. Focus 2.0tdci 136bhp crankshaft bolt torque setting Focus 2.0tdci 136bhp crankshaft bolt torque setting Ford Model: Focus mk2 2.0tdci zetec s 136bhp Ford Year Lower Control Arm (LCA) torque spec question. Hi Guys, This is the first time that I removed my lower control arm right side and I was reading the Haynes manual about the torque specs which I'm a little bit confuse. •Step 1 (inner rear bolt/nut) 74 ft-lbs. •Step 2 (inner rear bolt/nut) Tighten an additional 60º. Ford Focus Mk2 Forum (2004-2010) Driveshaft Torque Bolt Setting. blue]Dreamscience Enabled 180bhp 335lbft Torque[/color] WWW.PRODIGYMOTORSPORT.CO.UK 1209 posts · Joined 2018. #1 · Jan 9, 2020 (Edited by Moderator) Torque (lb ft) Notes Suspension. Front Suspension. steering column shaft bolt 21 front stabilizer bar link lower nuts 46 tie rod end nut 35 exhaust pipe hanger assembly bolts 18 engine roll restrictor bolt 63 front subframe bracket bolts 35 braket to front subframe bolts 46 277 Answers. SOURCE: torque wrench settings for ford focus thermostat. There is a set spec, but for the DIY mechanic,, Using a !/4 " drive, with the correct long socket, apply a FIRM effort on the wrench, but obviously not too much, as to sheer the studs. Always use a NEW gasket on all mating surfaces. 4UNo.

ford focus mk2 torque settings